Aluminum Mini ITX Case with PCIe 3.0 Riser, JOYJOM Mini PC Case, SFF Small Form Factor PC Case, TX Computer Gaming Case Supports GPU Graphics Card (Black)

I am very satisfied with how much I was able to shrink the footprint of my PC. I had a small 16L cube. This thing takes up less than half the size of it. I like aluminum cases. Aluminum is a soft metal and will scratch easy if you're rough with it, but it makes the case very light. No room for a traditional case fan. No problem. Heat has not been an issue whatsoever (I do not overclock, not a gaming hobbyist).I did need to get a low-profile CPU cooler, which I did not expect. I could have figured it out with the posted measurements, but assumed the "stock" CPU cooler would work. Only the 36mm height CPU coolers can fit here.Assembly was... like a solving a puzzle. Components need to be installed in the correct order. If you forget something you may find yourself needing to undo a lot of work to fix the situation. For example: did not install my m.2. storage drive before I put the motherboard in. The m.2. port is at the bottom of the motherboard. Can't access while installed because the GPU is blocking it. This means needing to remove the GPU extension, and removing either the GPU or the motherboard in order to get to the port.Overall, it was only tedious because of my own decisions and not because of the design of the case.Other important thing to note: only a 1u or flex atx power supply fits, and these do make some more noise than the typical PSU. BUT there is a custom option made by HDPlex that is fanless. It is a power converter that fits inside the case very easily, which you can then connect to a compatible power adapter. They recommend one on their website. This power situation makes this little case WAY more attractive.I'm definitely satisfied. If you want a small case go for it. It's a good price for a case and included PCIe Extension.

Great case layout super portable. Should have included pci riser 4.0 srews ok the outside of the case should have been bigger to fix threading on smaller screws. Wish it had usb c instead of usb 2.0 port. If you are looking for a case to fir in a bad this is a great option at a better price.

I bought two of these cases as a mini desktops and then started modding. Systems are both Asrock Z690m-itx, 14900k and a 12700K, 64gb Crucial ddr4-3200 with heatsink, 2x Crucial 2tb gen4, RX 6650xt and other 3070FE, both have a Intel RH1 cooler and 600 watt PS. (won't clear a stock Intel cooler without cutting out a hole in the side panel)Modded the case with a Dremel. Measured and cut the access for the cpu fan and GPU. Total time to mod each case with trial and error= 45 minutes.Temps go over 100 and throttled during benchmarks on the 14900k, but the 12700k was at 92 and got a better 3dmark score. Temps were 40-75 on Win11 with no case fans. For everyday and gaming, it is the smallest case I could find that would fit stuff.PCIe riser cable is gen3 and is replaceable with a Gen4 one if needed. Yes, I like the Intel RH1 cooler, the RGB's on it are cool, but not my thing.TLDR- Great case. Easy to mod for full size cards. Dremel's are great. 12700k runs cooler.

Got my system up and running with the included riser cable and it crashed constantly. So I took out the cable and booted everything on its own, no issues. Then I read that the riser is PCIE gen 3, my components were gen 4 so I tried to force gen 3. Still crashed with the riser. Tried reseating the riser again and it straight up died.If you want this case, get a separate PCIE riser and just avoid the headache.

Been looking at the K39 and similar cases for a while, and fell upon this brand, really like it. Simple to build in. almost every panel comes off, held in with combination of screws and rubber feet which hook into another panel.no instructions with this kit, and its the smallest case i have yet. paired it with a noctua sff cooler and its pretty bad @$$. so happy i now joined the SFF club.

Overall a pretty good budget case. However, I believe they did cut corners on the riser cable. I assembled my system with a Asus B790i, single fan modified RTX3060ti. After getting everything to fit, my PC would crash every time I ran Heaven benchmark. I thought the video card was at fault, perhaps after I made it into a single fan card. I had a 3060ti founders edition laying around and squeezed card in there with the front cover of the case off. Again PC would crash. Then I tried an old GTX1650 super and the PC would not crash, but I noticed that the fps would fall and come back up. I took everything apart on the bench and plugged my 3060ti directly into the mother board this time and everything ran fine, went through an hour of Heaven and Furmark with no issues. I installed the riser cable while on the bench and that is when the system started crashing. I bought a PUSOKEI PCIE 4.0 x16 riser cable, same style but white because Amazon had it same day delivery. Plugged that new riser cable in and the system was running like a champ at full speed. So my conclusion is that the riser cable that came with the case is suitable for older cards, but may not have proper shielding for new cards.

The case looks nice and the Apevia SFF power supply fit perfectly. However, my ASROCK Z790 ITX motherboard with a Noctua Ultra Low Profile CPU Cooler would not fit and be able to screw down the side cover to the case. Any other CPU cooler would be totally out of the question. A real shame as I really liked the design. The case just needs to be one inch wider on the side with the mobo and it would be perfect.

Build quality surpassed my expectations, a tight little case that looks great. My only suggestion would be more perforation for air flow. CPU stays cool enough but the gpu gets a little warm, an adjustment to fan curve fixes this, but extra air would allow for a quieter machine. Would buy again